 |
|
|
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
|
|
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
HO Turntables
A Bowser turntable is made of 1/2" plywood with a brass pit wall, the wood is painted gray; the pit rail is installed and the wiring done. The center shaft , bearings and bogies are installed on the wooden bridge beam. Track and is NOT included. The bridge will accept any type of track you like. A turntable requires a square hole 2" larger than the bridge length and at least 6" of clearance under the layout. The motor requires and N or HO transformer (only controls the rotation of bridge) to move the bridge clockwise or counterclockwise. When the bridge is stopped it is locked in place. You can move the bridge very slowly. This allows you to align the track for the loco to pull onto the bridge. An automatic indexing system (stop at the next track automatically) is made by Dallee Electronic. The Dallee unit stops the bridge at each track without you having to align it. The Dallee Indexer is mounted under the layout and can be installed after the turntable is in your layout without having to tear it apart .
HO turntable with our new deck detail kit. Detail kit fits 14",16" & 18" turntables.
KIT INCLUDES: brass middle tower, brass handrail wire, brass handrail stanchions, pewter shanty, bogie wheel brackets, wood decking and wood ties for decking.Other photos of new deck detail kit: Picture 1, Picture 2, Picture 3
Assembly- Exploded View Drawings
More Instructions - these are O gauge but the assembly the same
Turntable Pricing - see price list
Turntable Kits Complete
(includes turntable with pit and bridge, girder kit, deck detail kit & motorizing kit.)
NO OTHER PARTS ARE REQUIRED
#7914 - 14" Turntable Complete $357.00
#7916 - 16" Turntable Complete $360.00
#7918 - 18" Turntable Complete $363.00Shipping and handling for HO turntables $18.00
Turntable Indexing Kit by Dallee Electronics.
Not included with Bowser turntables. You do not always need this kit.
(Stops at any location you set. Mounts under turntable, infinite number of stops.)
#213-617 Indexing Kit by Dallee Electronics. $74.95
The following is a link to Dallee Indexer Instruction Page
http://www.dallee.com/Turntable.htm
HO turntable deck detail kit only. Detail kit fits 14",16" & 18" turntables.
Available separately if you already have an old BOWSER turntable.#7904 $50.00
Cast parts in the Deck Detail Kit
Repair and new versions of parts.
79215 Bridge Bushing - holds shaft to wood bridge beam
932043 6-32 X 1/4 SOCKET HEAD CAP SCREW
79214 Pit Bushing - shaft passes through this bushing in the
bottom of the pit.
79134 HO Shaft - 5/16 diameter steel
79234 O Shaft - 5/16 diameter steel
79477 HO Bridge Bogie - wheel assembly that is mounted on
each end of wood beam
79218 Drive wheel clamp - holds drive wheel to the shaft
79330 Set collar - slides on shaft between bridge and pit bushing
932043 6-32 X 1/4 SOCKET HEAD CAP SCREW
Pictures of 18" turntable as shipped from Bowser.
Picture 1: Top view, two wires on bridge are attached to the track.
Picture 2: Side view of underside with drive wheel and packing blocks in place.
Picture 3: Underside view with packing blocks in place
Picture 4: Drive wheel removed. Packing blocks removed from drive wheel.
Two wires that are attached to our transformer.
One allen wrench used to remove drive wheel.
Picture 5: Picture of Girders for turntable sides
We cannot supply Korber HO Roundhouses
